Well the method described by Aaron kunze works well even on Boston Harbor board but make sure that u use a Cross Ethernet Cable. Rgds Ravi Jorge Hermosillo G wrote:Hi Irvin, I am forwarding you a previous e-mail from Aaron Kunze that helped us a lot in doing what you are trying to do, in an ENP2505 board from Radisys. We succesfully have tried running C code from the workbench in the board following this. Hope this help you. Jorge Hermosillo Najati, If you are using the workbench, the process for loading microC is the same as the process for loading microengine assembly. It's been a long time since I've loaded any code without the microACE framework, so my memory is rusty. :) If your board is running Linux, you have to make sure that the ue.o driver is loaded and that the rs_udebug process is running in the background. Both of these ship with the SDK and can be found in ixasdk/bin/arm-be. Then, in the workbench hardware settings on your development system, say "Connect via Ethernet" and give it the IP address of the debug port of the board. If you are using VxWorks, the development system side is the same, but on the board you need to run VxWorksNetApp.o. There is a readme file with the workbench that can walk you through this process. It is called VxWorksBuild_ReadMe.txt. Hope this helps! Aaron ------------------------ Aaron Kunze Intel Labs aaron.kunze@intel.com -PGP Key ID: 0x81124B7C- -NOT SPEAKING FOR INTEL- ------GO BOILERS!!------

-----Original Message----- From: Najati Imam [mailto:nrimam0@uky.edu] Sent: Wednesday, September 04, 2002 1:47 PM To: ixp1200@CS.Princeton.EDU Subject: Re: [ixp1200] microC development

...

Let me clarify this a bit. Development of microC *microACEs* is not supported by Intel in IXA SDK 2.x. Use of microC outside of the microACE framework is supported and microC code will run on the IXP1200 hardware.

Oh? thats cool. What does one need as far as run time environment to do so? Namely, can one take a uof compiled from the workbench and start it on a microengine(s) and if so how?

guilt

--------------------------------- Do you Yahoo!? U2 on LAUNCH - Exclusive medley & videos from Greatest Hits CD

Hi, U can use serial port method to connect to the hardware but I have never tried it.Also I guess it would be very slow, better go for ethernet. Rgds Ravi Modgekar NING WENG wrote: How about using only serial cable? On Fri, 8 Nov 2002, Ravi modgekar wrote:

Well the method described by Aaron kunze works well even on Boston Harbor board but make sure that u use a Cross Ethernet Cable. Rgds Ravi Jorge Hermosillo G wrote:Hi Irvin,

I am forwarding you a previous e-mail from Aaron Kunze that helped us a lot in doing what you are trying to do, in an ENP2505 board from Radisys. We succesfully have tried running C code from the workbench in the board following this.

Hope this help you.

Jorge Hermosillo

Najati,

If you are using the workbench, the process for loading microC is the same as the process for loading microengine assembly. It's been a long time since I've loaded any code without the microACE framework, so my memory is rusty. :) If your board is running Linux, you have to make sure that the ue.o driver is loaded and that the rs_udebug process is running in the background. Both of these ship with the SDK and can be found in ixasdk/bin/arm-be. Then, in the workbench hardware settings on your development system, say "Connect via Ethernet" and give it the IP address of the debug port of the board.

If you are using VxWorks, the development system side is the same, but on the board you need to run VxWorksNetApp.o. There is a readme file with the workbench that can walk you through this process. It is called VxWorksBuild_ReadMe.txt.

Hope this helps!

Aaron

------------------------ Aaron Kunze Intel Labs aaron.kunze@intel.com -PGP Key ID: 0x81124B7C- -NOT SPEAKING FOR INTEL- ------GO BOILERS!!------

...

-----Original Message----- From: Najati Imam [mailto:nrimam0@uky.edu] Sent: Wednesday, September 04, 2002 1:47 PM To: ixp1200@CS.Princeton.EDU Subject: Re: [ixp1200] microC development

...

Let me clarify this a bit. Development of microC *microACEs* is not supported by Intel in IXA SDK 2.x. Use of microC outside of the microACE framework is supported and microC code will run on the IXP1200 hardware.

Oh? thats cool. What does one need as far as run time environment to do so? Namely, can one take a uof compiled from the workbench and start it on a microengine(s) and if so how?

guilt

--------------------------------- Do you Yahoo!? U2 on LAUNCH - Exclusive medley & videos from Greatest Hits CD

--------------------------------- Do you Yahoo!? U2 on LAUNCH - Exclusive medley & videos from Greatest Hits CD