Vikram You are welcome to try this code (below) I've used it on the IXP1200 dev board, I don't know how much different this is to your board. Rgds Mick /*************************************************************************** *** * * PHY.C * * Access MII and symbol PHYs. * * Revision history : Created March 1997 Updated October 2001 Updated April 2003 * WARRANTY DISCLAIMER. INTEL AND ITS SUPPLIERS MAKE NO WARRANTIES WITH RESPECT TO TECHNOLOGY, EITHER EXPRESS OR IMPLIED, INCLUDING ANY IMPLIED WARRANTIES OF SATISFACTORY QUALITY OR FITNESS FOR A PARTICULAR PURPOSE OR ANY IMPLIED WARRANTY OF NONINFRINGEMENT. TECHNOLOGY IS PROVIDED AS IS, WITHOUT WARRANTY OF ANY KIND. LIMITATION OF LIABILITY. INTEL AND ITS SUPPLIERS SHALL NOT BE LIABLE FOR ANY PROPERTY DAMAGE, PERSONAL INJURY, LOSS OF PROFITS, LOSS OR CORRUPTION OF DATA OR USE, INTERRUPTION OF BUSINESS OR ANY SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL OR PUNITIVE DAMAGES, HOWEVER CAUSED, WHETHER FOR BREACH OF WARRANTY, CONTRACT, STRICT LIABILITY OR OTHERWISE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE OR LOSS. INTEL AND ITS SUPPLIERS DISCLAIM ALL LIABILITY, INCLUDING LIABILITY FOR INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHTS RELATING TO THE TECHNOLOGY PROVIDED. IT IS THE RECIPIENTS OBLIGATION TO BACK-UP OR SAVE ANY STORED DATA. **************************************************************************** **/ #include typedef unsigned char BYTE; typedef unsigned short WORD; typedef unsigned long DWORD; /* functions' prototypes*/ int PHYread_reg (int port, int phyadd, int reg_offset); int PHYwrite_reg (int port, int phyadd, int reg_offset, unsigned short value); void LED_FLASH (); /* static functions*/ static void PHYgen_tristate (int base_port); static void PHYwrite_mii (int base_port, DWORD mii_data, int size); static int SERCOMread_reg (int port); static void SERCOMwrite_reg (int port, DWORD value); /*-------------------------------------------------------------------------- -- | MII management : | | | | The MII management interface consists of two pins : MDIO and MDC. | | When reading or writing a bit from/to the PHY, its value should be | | read or written to MDIO and MDC should be rotated (once high and once| | low). | | | |--------------------------------------------------------------------------- -- | Accessing MII management through the dec21440: | | | | SER_COM register has 3 relevant bits: | | | | MDM : Mii Data Mode : setting this bit sets the MDIO pin to output mode, | | resetting it sets the pin to input mode. | | MDC : writing this bit sets the MDC pin | | MDIO : writing this bit sets the MDIO pin, reading this bit reads the| | value from the MDIO pin. | | | ---------------------------------------------------------------------------- */ /*========================================================================== ====== = Accessing MII PHY registers : = = The management should write the following frame to the MII PHY : = = +----------------------------------------------------------------+ = | Management frame fields | = +------+-------+----+----+-------+-------+----+------------------+-----+ = | | PRE | ST | OP | PHYAD | REGAD | TA | DATA |IDLE | = +------+-------+----+----+-------+-------+----+------------------+-----+ = |Read | 1...1 | 01 | 10 | AAAAA | RRRRR | Z0 | DDDDDDDDDDDDDDDD | Z | = +------+-------+----+----+-------+-------+----+------------------+-----+ = |Write | 1...1 | 01 | 01 | AAAAA | RRRRR | 10 | DDDDDDDDDDDDDDDD | Z | = +------+-------+----+----+-------+-------+----+------------------+-----+ = = PRE : preamble (32 bits of '1' on MDIO) = ST : Start frame = OP : operation mode (read or write) = PHYADD : Phy address = REGADD : Register's internal address = TA : turnaround - in 'read' operation - tristate on the MII's IO pin, the phy = should write '0' on the next MCLK cycle. = in 'write' operation - write 10 on the IO pin. = DATA : register's contents (16 bits) on MDIO = ============================================================================ ====*/ #define MII_ACS_PREAMBLE 0xFFFFFFFF #define MII_ACS_PREAMBLE_LEN 32 #define MII_ACS_READ_MASK 0x60000000 #define MII_ACS_WRITE_MASK 0x50020000 #define MII_ACS_PHYADD_ALIGN 23 #define MII_ACS_REGADD_ALIGN 18 #define SER_COM (0x8 * 0x4) #define MDM 0x20 #define MDIO 0x10 #define MDC 0x8 #define MDIO_BIT_POSITION 4 #define PASS 0 #define FAIL 0xFFFF /*************************************************************************** ** PHYread_reg This function reads an MII PHY registers. Input parameters: int port - the IXF440 port number int phyadd - the PHY address int reg_offset - the PHY's register offset Output parameters: none Return value: Data from PHY if the reading succeded (the PHY responded), FAIL otherwise. **************************************************************************** / int PHYread_reg (int port, int phyadd, int reg_offset) { int base_port, frame, value, retval, i; BYTE ser_val, dbit; /* write preamble*/ PHYwrite_mii (port, MII_ACS_PREAMBLE, MII_ACS_PREAMBLE_LEN); /* prepare command word*/ frame = phyadd << MII_ACS_PHYADD_ALIGN; frame |= reg_offset << MII_ACS_REGADD_ALIGN; frame |= MII_ACS_READ_MASK; PHYwrite_mii (port, frame, 14); /* tristate*/ PHYgen_tristate (port); /* check that the PHY responded with zero bit*/ ser_val = SERCOMread_reg (port); if ((ser_val & MDIO) != 0) retval = FAIL; /* read data from PHY*/ ser_val &= ~MDM & ~MDC ; /* change to input mode*/ for (i=0; i< 16; i++) { SERCOMwrite_reg (port, ser_val); SERCOMwrite_reg (port, ser_val | MDC); ; dbit = ((BYTE)(SERCOMread_reg (port)) & MDIO) >> MDIO_BIT_POSITION; (value) = ((value) << 1) | dbit; } PHYgen_tristate (base_port); return (value); } /*************************************************************************** ** PHYwrite_reg This function writes an MII PHY register. Input parameters: int port - the IXF440 port number int phyadd - the PHY address int reg_offset - the PHY's register offset unsigned short value - the value to be written to the register. Return value: none. **************************************************************************** / int PHYwrite_reg (int port, int phyadd, int reg_offset, unsigned short value) { int base_port; DWORD frame; /* write preamble */ PHYwrite_mii (port, MII_ACS_PREAMBLE, MII_ACS_PREAMBLE_LEN); /* prepare command word */ frame = phyadd << MII_ACS_PHYADD_ALIGN; frame |= reg_offset << MII_ACS_REGADD_ALIGN; frame |= MII_ACS_WRITE_MASK; PHYwrite_mii (port, frame, 16); /* write data */ PHYwrite_mii (port, (DWORD)value << 16, 16); PHYgen_tristate (port); return(PASS); } /*************************************************************************** ** PHYwrite_mii This function writes a buffer of data to the MII phy. Input parameters: int base_port - the IXF440 port to which we should write SER_COM (port 0 of the chip on which our port is) DWORD mii_data - the data buffer to write to the PHY. The data will be written with MSB first. int size - the size of data (in bits) we wish to write. Return value: none **************************************************************************** / static void PHYwrite_mii (int port, DWORD mii_data, int size) { BYTE dbit, /* data bit */ ser_val; int i,j; ser_val = (BYTE)(SERCOMread_reg (port)) & (~MDC & ~MDIO & MDM); /* leave only the bits not related to PHY access*/ for (i=size; i>0; i--) { dbit = (BYTE)(mii_data >> (31 - MDIO_BIT_POSITION)) & MDIO; SERCOMwrite_reg (port, ser_val | MDM | dbit ); j++; /*slow the loop down*/ SERCOMwrite_reg (port, ser_val | dbit | MDM | MDC); mii_data = mii_data << 1; } } /*************************************************************************** ** PHYgen_tristate This function generates tristate on the phy's MDIO pin. Input parameters: int base_port - the IXF440 port to which we should write SER_COM (port 0 of the chip on which our port is) Return value: PASS if the reading succeded (the PHY responded), FAIL otherwise. **************************************************************************** / #define MII_WRITE_TS 0 static void PHYgen_tristate (int port){ BYTE ser_val; ser_val = (BYTE)(SERCOMread_reg (port)) & (~MDIO & ~MDC & ~MDM); SERCOMwrite_reg (port, ser_val | MII_WRITE_TS); SERCOMwrite_reg (port, ser_val | MII_WRITE_TS | MDC); } /*************************************************************************** ** SERCOMread_reg This function reads data from the MAC ser_com port. Input parameters: int base_port - the IXF440 port to which we should read from SER_COM (port 0 of the chip on which our port is) Return value: data from PHY if the reading succeded (the PHY responded), FAIL otherwise. **************************************************************************** / static int SERCOMread_reg (int base_port) { int *p_SER_COM, value; p_SER_COM=0x38400020; value = *p_SER_COM; return (value); } /*************************************************************************** ** SERCOMwrite_reg This function writes data to the MAC ser_com port. Input parameters: int base_port - the IXF440 port to which we should read from SER_COM (port 0 of the chip on which our port is) Return value: none **************************************************************************** / static void SERCOMwrite_reg (int port, DWORD value) { int *p_SER_COM; p_SER_COM=0x38400020; *p_SER_COM = value; } void LED_FLASH () { int *p_GMII_MNG_ACC; int value; /*turn off the gigabit MDIO,MDC as these lines are shared*/ p_GMII_MNG_ACC=0x038408128; *p_GMII_MNG_ACC=0x0; /*flash the leds on port0 phy*/ PHYwrite_reg(0x0,0x0,0x14,0xBBB2); }