December 2002 - ixp1200 - lists.cs.princeton.edu

L2L3NAT_8_1Gig_hw memory initialization location
by Eng Kean 03 Jan '03

03 Jan '03

anybody know which SRAM, SDRAM, and Scratchpad memory location should be initialized before running simulation? so that a script to initialize that specific memory location. thanks. __________________________________________________ Do you Yahoo!? Yahoo! Mail Plus - Powerful. Affordable. Sign up now. http://mailplus.yahoo.com

4 3

minimal starting code
by Najati Imam 30 Dec '02

30 Dec '02

I'm trying to get around using ixstart and ixstop and do port/uengine initialization manually. My motivation for doing so is to avoid having to use ixsys.config's ambiguous initialization directives and have a bit better control over which engines get which uof and get a better grasp on which me-to-me rings I can use, how I initialize/allocate them. I figured dredging through ixconfig's source code would be the best place to start but its covered in crosscalls and I really don't want to deal with all that. Is there no simple function call to say "give port 0 mac address ..." or "put port 0 in promiscious mode" and the many other things that need to be done to get a port ready for a ueng to use it. I'd also like to use the supplied ingress microcode, slightly modified, without the provided core component but will need to discover what values to patch the .import_vars to from the ingress code. I've looked through that a little today and it seems to be about as friendly as dealing with crosscalls. If anyone has either done this or has some leads that would make my doing it easier either would be appreciated. thanks, Najati ___________________________________________________________ /Najati Imam . najati(a)netlab.uky.edu . "Don't Ever Give Up"\ \Laboratory for Advanced Networking . University of Kentucky/

1 0

L2L3NAT_8_1Gig_hw cannot be run
by Eng Kean 23 Dec '02

23 Dec '02

hi, Does anyone try to run simulation of L2L3NAT_8_1Gig_hw project provided by SDK2.01 vol.II? I found that when running this project under simulation mode, SDRAM initialization error will occur. Can anybody suggest solution for this? Thanks. __________________________________________________ Do you Yahoo!? Yahoo! Mail Plus - Powerful. Affordable. Sign up now. http://mailplus.yahoo.com

2 1

uDbg Library Wrappers for linux...
by Austen McDonald 21 Dec '02

21 Dec '02

Ive looked but I can't find wrappers for the uDbg calls into the ue driver---i.e., I can't find a file akin to SA1_CoreLibs/uelib/ueng_lib.c that wraps the ioctl's responsible for the uEng library calls. Does a similar file for the uDbg calls not exist? (Im implementing an interactive debugger that's why Im asking). Austen McDonald austen(a)cc.gatech.edu God does not care about our mathematical difficulties. He integrates empirically. -- Albert Einstein

1 0

Problem running IXP1200 VERA apps
by Magesh Kannan 20 Dec '02

20 Dec '02

Hi, Thanks to some help from this group, I managed to build the IXP1200 applications for Vera. I also built and ran the Hello World test program. Now I have a problem running the IPmm and PktGen applications. When I invoke 'sgo ipmm.srec', the output on the board's serial port stops abruptly. Here is the output. =============================== Jumping to: 0xC1002000 bss_start = 0xC10121A8 bss_end = 0xC1012A40 (length) = 0x00000898 Sbrk_heap_ptr_ = 0xC1013000 Sbrk_heap_end_ = 0xC1CF8000 (length) = 0x00CE5000 (13204 Kbytes) Enabling MMU MMU enabled Calling sram_init() Calling scratch_init() Calling PCI_mapout_init() PCI_mapout_init: PCI_dram_siz = 0x02000000 PCI_mapout_init: PCI_dram_bar = 0xF6000000 Calling my_main() Starting uEngines and control program. --- Control_SystemStart --- Contr ========================== This happens irrespective of if I build the microcode with or without VRP. The LED displays 0x25. The same happens with the application PktGen. What have I done wrong here? Thanks, Magesh

6 9

rtm trie structure!
by adarsh daheriya 17 Dec '02

17 Dec '02

hi! can anybody please tell me which variation of trie structure is implemented in the rtm (Route Table Manager) application used with the L3fwd codes shipped with the 'ixp1200 sdk 2.01'. regards, -Adarsh.

1 0

Re: [ixp1200] rs_udebug fails
by Shyamal Pandya 15 Dec '02

15 Dec '02

However, it still times out after a while and exits. Cannot register service: RPC: Timed out unable to register (SA1200TARGET, SA1200VERSION, udp). [1]+ Exit 1 ./rs_udebug I don't have a clue what to do... -- Shyamal Pandya Cogito, ergo sum! Addr: 920 S Terrace Rd #102 Tempe AZ 85281 Phone: 1-480-96601982 >From: "Shyamal Pandya" <shyamalpandya(a)hotmail.com> >Reply-To: ixp1200(a)CS.Princeton.EDU >To: ixp1200(a)CS.Princeton.EDU >Subject: Re: [ixp1200] rs_udebug fails >Date: Sun, 15 Dec 2002 04:34:51 -0700 > >Ashish, >Thanks! >lo was not properly configured. > > > >-- >Shyamal Pandya > >Cogito, ergo sum! > >Addr: >920 S Terrace Rd #102 >Tempe AZ 85281 >Phone: >1-480-96601982 > > > > > >>From: Rayashish(a)aol.com >>Reply-To: ixp1200(a)CS.Princeton.EDU >>To: ixp1200(a)CS.Princeton.EDU >>Subject: Re: [ixp1200] rs_udebug fails >>Date: Fri, 13 Dec 2002 13:10:43 EST >> >>Shyamal, >> >>fiirst configure the ethernet and loopback interfaces and then run >>rs_udebug. >> >>--Ashish >>Dept. of Computer Engineering >>San Jose State University >>San Jose, CA >> >> >>In a message dated 12/13/2002 4:35:40 AM Pacific Standard Time, >>shyamalpandya(a)hotmail.com writes: >> >> >> > When I try running rs_udebug on an ENP-2505 board, it fails >> > with the following error: >> > >> > Device lo is down. >> > Device lo is down. >> > Cannot register service: RPC: Unable to send; errno = No buffer space >> > available >> > unable to register (SA1200TARGET, SA1200VERSION, udp). >> > >> > >> > The ue.o, pciDg-arm.o and pciDgNet-arm.o modules are loaded. >> > >> > >> > >> > > >_________________________________________________________________ >Add photos to your e-mail with MSN 8. Get 2 months FREE*. >http://join.msn.com/?page=features/featuredemail _________________________________________________________________ The new MSN 8: smart spam protection and 2 months FREE* http://join.msn.com/?page=features/junkmail

1 0

Re: [ixp1200] rs_udebug fails
by Shyamal Pandya 15 Dec '02

15 Dec '02

Ashish, Thanks! lo was not properly configured. -- Shyamal Pandya Cogito, ergo sum! Addr: 920 S Terrace Rd #102 Tempe AZ 85281 Phone: 1-480-96601982 >From: Rayashish(a)aol.com >Reply-To: ixp1200(a)CS.Princeton.EDU >To: ixp1200(a)CS.Princeton.EDU >Subject: Re: [ixp1200] rs_udebug fails >Date: Fri, 13 Dec 2002 13:10:43 EST > >Shyamal, > >fiirst configure the ethernet and loopback interfaces and then run >rs_udebug. > >--Ashish >Dept. of Computer Engineering >San Jose State University >San Jose, CA > > >In a message dated 12/13/2002 4:35:40 AM Pacific Standard Time, >shyamalpandya(a)hotmail.com writes: > > > > When I try running rs_udebug on an ENP-2505 board, it fails > > with the following error: > > > > Device lo is down. > > Device lo is down. > > Cannot register service: RPC: Unable to send; errno = No buffer space > > available > > unable to register (SA1200TARGET, SA1200VERSION, udp). > > > > > > The ue.o, pciDg-arm.o and pciDgNet-arm.o modules are loaded. > > > > > > > _________________________________________________________________ Add photos to your e-mail with MSN 8. Get 2 months FREE*. http://join.msn.com/?page=features/featuredemail

1 0

Re: [ixp1200] rs_udebug fails
by Rayashish＠aol.com 13 Dec '02

13 Dec '02

Shyamal, fiirst configure the ethernet and loopback interfaces and then run rs_udebug. --Ashish Dept. of Computer Engineering San Jose State University San Jose, CA In a message dated 12/13/2002 4:35:40 AM Pacific Standard Time, shyamalpandya(a)hotmail.com writes: > When I try running rs_udebug on an ENP-2505 board, it fails > with the following error: > > Device lo is down. > Device lo is down. > Cannot register service: RPC: Unable to send; errno = No buffer space > available > unable to register (SA1200TARGET, SA1200VERSION, udp). > > > The ue.o, pciDg-arm.o and pciDgNet-arm.o modules are loaded. > > >

1 0

rs_udebug fails
by Shyamal Pandya 13 Dec '02

13 Dec '02

When I try running rs_udebug on an ENP-2505 board, it fails with the following error: Device lo is down. Device lo is down. Cannot register service: RPC: Unable to send; errno = No buffer space available unable to register (SA1200TARGET, SA1200VERSION, udp). The ue.o, pciDg-arm.o and pciDgNet-arm.o modules are loaded. Any tips??? -- Shyamal Pandya Addr: 920 S Terrace Rd #102 Tempe AZ 85281 Phone: 1-480-96601982 _________________________________________________________________ The new MSN 8: smart spam protection and 2 months FREE* http://join.msn.com/?page=features/junkmail

1 0