- ixp1200 - lists.cs.princeton.edu

Assembly succeeds with no microcode.
by Jagannathan Iyer Venkatesan 08 Apr '03

08 Apr '03

Hi, I have installed the Wine from winehq.com from the source Wine installed properly. But I am trying to do a make in my Libixprouter/ue/src. make does not complain about anything, except something in the .sed file. (Please refer log below). But there is no microcode in the microcode array as expected. For eg when I do "touch xmt.uc" and do a make, I expect the microcode in the xmt.x file but the xmt_uCodeArr[] array in xmt.x is empty. Can someone point out what is going wrong ? I can give more details. Thank you. Jagan. The output from make (collected as $make &> /tmp/make_out) after a touch xmt.uc is as follows. /* start of make - added by me */ -- preprocessing xmt -- For language 'english' several language ids were found: en_US - 0409; en_GB - 0809; en_AU - 0C09; en_CA - 1009; en_NZ - 1409; en_IE - 1809; en_ZA - 1C09; en_JM - 2009; en_ - 2409; en _BZ - 2809; en_TT - 2C09; Instead of using first in the list, suggest to define your LANG environment variable like this: LANG=en_US Assembly successful.^M -- allocating registers for xmt -- -- creating xmt.uca -- sed: file xmt.sed line 5: Invalid reference \2 on `s' command's RHS -- assembling xmt -- For language 'english' several language ids were found: en_US - 0409; en_GB - 0809; en_AU - 0C09; en_CA - 1009; en_NZ - 1409; en_IE - 1809; en_ZA - 1C09; en_JM - 2009; en_ - 2409; en _BZ - 2809; en_TT - 2C09; Instead of using first in the list, suggest to define your LANG environment variable like this: LANG=en_US Preprocessing successful; output file, "xmt.uci" written.^M ^M ^M Reading "xmt.uci": pass 1...^M Reading "xmt.uci": pass 2...^M ^M Number of uwords compiled: 0^M Number of pages compiled: 1^M Ucode output written to: "xmt.list"^M Assembly successful.^M -- extracting xmt -- perl: warning: Setting locale failed. perl: warning: Please check that your locale settings: LANGUAGE = (unset), LC_ALL = (unset), LC_CTYPE = "", LANG = "english" are supported and installed on your system. perl: warning: Falling back to the standard locale ("C"). rm xmt.sed /* end of make - added by me */

1 0

RE: [ixp1200] l3fwdr
by Botham, Mick 06 Apr '03

06 Apr '03

Kamesh, I'm not sure if this applies to the ENP-2305, but it did affect the IXP1200EB. Some PHY devices default 10MB mode is also loop-back mode, so on a 10MB connection, as soon as a packet is sent by the IXP1200 it gets looped back to the IXP1200, and so the process goes on, the result is a packet flood. The fix was either to connect to a 100MB device so the PHY would auto-negotiate to 100MB, or to program the PHY so that in 10MB mode it wasn't set to loopback. Rgds Mick Hi, Ping was not running. In fact the PC kind of hangs ie mouse pointer disappears etc when I connnect. I am able to see the output only after I disconnect. Configuration: Ethernet port 1 of ENP-2505 is connected back-to-back to the eth1 of the host PC ( PC in which the card is plugged in) through a crossover cable. The IP address of the IXP port is 192.168.1.150 and the IP address of the PC port is 192.168.1.3 . Also is there any option is the ixsys.config file through which I can specify the rate ? Thanks, Kamesh. Abhijeet Joglekar wrote: >Hi Kameswara, > >I guess you have already tried to connect the PC port to the IXP >port without going thro' the hub as Cyrus suggested. Just to rule >out any autonegotiation problems betweem 10/100 hub and IXP port. > >So is ping running when you captured that tcpdump output? >Also, what are the interface addresses of the IXP port >and the PC port in your setup? > >-- abhijeet > >On Thu, 3 Apr 2003, Kameswara Avasarala wrote: > > > >>Hi, >> This is what I observe if I do a tcpdump. >> >> >>Cyrus Hall wrote: >> >> >> >>>Hi there- >>> >>>You mention a great deal of link level activity. Have you done a TCP >>>dump? I had my ENP-2505 hooked up to a 10 Mbps hub which was causing >>>all sorts of issues, including a packet flood to be issued from the card >>>whenever I tried to start up a uACE. Make sure all interfaces are 100 >>>Mbps and see if that helps... >>> >>> >>> > > >

1 0

RE: [ixp1200] How to generate asm code from SDK
by Heaton, Eric D 04 Apr '03

04 Apr '03

Yan, This warning should have no effect on the production of an .asm file. Of course, if you had errors in your build, that is a different story. Check your build directory for a file named <c_file_with_main_in_it>.asm if you didn't specify a specific name with the -Fa switch. But note that you can look at the assembly code generated from a Microengine C file easily without using the -Fa switch. When using the Workbench (v2.01) in debug mode, choosing a thread to view will, by default, display the source code for the thread. However, there is a toggle switch on that window (it has a yellow and green page icon circularly pointing to each other) that will display the .list file containing the assembly for the source code line your cursor is currently on. Check it out! --eric h. -----Original Message----- From: Yan Luo [mailto:yluo@cs.ucr.edu] Sent: Sunday, January 12, 2003 12:02 PM To: ixp1200(a)CS.Princeton.EDU Subject: [ixp1200] How to generate asm code from SDK HI, I try to generate the assembly code from Micro C code using SDK 2.0, In the Build->setting, I check the "Produce assembly code file". When I compile , I got the following warning: (0): warning : IPO enabled; -Fa and -FA produce dummy .asm files It seems it did not produce asm file, and I cannot find asm file anywhere. How can I get the assembly code? Thanks, Yan

10 25

Re: [ixp1200] qstn abt debug option and l3fwdr
by Shyamal Pandya 04 Apr '03

04 Apr '03

Hi Srini, TO make DBG_MSG work you will have to modify the l3fwdr Makefile and recompile. Specifically, in the file src/microace/aces/l3forward_ace/Makefile, the assignment to the MORE_DEFS variable will have to include L3FWD_DEBUG. There is a commented MORE_DEFS assignment that includes the option. -- Shyamal Pandya Arizona State University Addr: 920 S Terrace Rd #102 Tempe AZ 85281 Phone: 1-480-966-1982 >From: Srinivasan Krishnamoorthy <sriniskm(a)yahoo.com> >Reply-To: ixp1200(a)CS.Princeton.EDU >To: ixp1200(a)CS.Princeton.EDU >Subject: [ixp1200] qstn abt debug option and l3fwdr >Date: Thu, 3 Apr 2003 01:46:17 -0800 (PST) > >Hi, > >I am using the L3Fwdr. I would like to see the flow of >the code. How do I set up the debug option so that all >the DBG_MSG gets printed on the screen? > >Also, I have a problem with pinging a system connected >to one port(say port0) of the IXP from another system >connected to another port(say port1) of the IXP(i.e, >the systems are in different subnets), when i use the >L3fwdr. Hope I make sense!! I am just starting the >ixsys.config-l3fwdr. Am I missing something here? > >Thanks >Srini > >__________________________________________________ >Do you Yahoo!? >Yahoo! Tax Center - File online, calculators, forms, and more >http://tax.yahoo.com _________________________________________________________________ STOP MORE SPAM with the new MSN 8 and get 2 months FREE* http://join.msn.com/?page=features/junkmail

1 0

bug in ue driver
by Shyamal Pandya 03 Apr '03

03 Apr '03

Hi, I noticed a bug in the ue driver. In the file src/microace/comon/wbench/SA1_CoreLibs/ue/main.c, funcion ue_ioctl, the switch statement has case UENG_SETCTXSIGEVENTS within which the function uEng_setCtxWakeupEvents is called, which should be a call to uEng_setCtxSigEvents. Because of this an ioctl call with parameter UENG_SETCTXSIGEVENTS will result in writes to the CTX_*_WAKEUP_EVENTS registers instead of the signal events registers of the microengine. -- Shyamal Pandya Arizona State University Addr: 920 S Terrace Rd #102 Tempe AZ 85281 Phone: 1-480-966-1982 _________________________________________________________________ Help STOP SPAM with the new MSN 8 and get 2 months FREE* http://join.msn.com/?page=features/junkmail

2 1

Porting VERA?
by Øyvind Hvamstad 01 Apr '03

01 Apr '03

Hi, I'm currently writing a thesis that use the ENP-2505 card. In this project I would like to make use of the existing VERA software. However, I see on the list that VERA isn't compatible with the ENP-2505. My questions are: Are there any plans on porting VERA to work with the ENP-2505, and if so, how much coding will it involve? I will gladly help, but not if it takes to long. If no plans are made, please let me know, so I can rethink my work. In advance, thanks! Øyvind Hvamstad

2 1

route_add() problem
by Li Zhao 31 Mar '03

31 Mar '03

Hi, I want to put a large routing table to the L3fwd16 project in the IXP 1200 simulator. I changed the size of the sram and some parameters in mem_map.h. But it seems that the functions route_add() and ht_add() donot read the mem_map.h file at all. The route_add() gave some error message after reading about 200 routes. Then the IXP 1200 simulator crashed. Since these two functions are from the dll library, the implementation is unknown to me. Are they compiled with the fixed SRAM size and sram_route_base parameter? If so, is there anyway I can do to insert the large routing table? Thanks a lot! -- Li Zhao Dept. of Computer Science Univ. of California, Riverside Tel:1-909-787-2001

1 0

SA interrupt
by Shyamal Pandya 23 Mar '03

23 Mar '03

Hi, I want to deliver an interrupt from the microengines to the Strong core processor of the IXP1200. The core runs Linux. After reading through the source code of the microengine driver, I figure that each time the microengines are initialized, the ue driver registers an interrupt handler with the linux kernel for a microengine interrupt. There is also a function uEng_intConnect, that can be used to register a handler function with this driver. (For example the debug library uses the function to register some function). But this function is not exported to the outside world. If it were, then one would do something like write a module stacked on the ue module and use the uEng_intConnect function to register its own handler function. I cannot avoid not using the ue driver because I am using the MicroACE framework. What can be done so that somehow I can catch a microengine interrupt on the core processor? I don't know if I have been quite clear, but I will appreciate any help. Thanks! -- Shyamal Pandya Addr: 920 S Terrace Rd #102 Tempe AZ 85281 Phone: 1-480-96601982 _________________________________________________________________ Tired of spam? Get advanced junk mail protection with MSN 8. http://join.msn.com/?page=features/junkmail

2 1

Flow table initialization in NAT microACE
by Eng Kean 23 Mar '03

23 Mar '03

Hi, How the flow tables in NAT microACE are initialized? How flow entries are added and deleted? Which source files are involved? Thanks & regards, Eng Kean __________________________________________________ Do you Yahoo!? Yahoo! Platinum - Watch CBS' NCAA March Madness, live on your desktop! http://platinum.yahoo.com

1 0

RE: [ixp1200] SA interrupt
by Arthur Berkovitch 23 Mar '03

23 Mar '03

Hi, I do exactly as you described with uEng_intConnect, but with VxWorks and without MicroACE. It works fine! I looked at the ixasdk2.0 /opt/ixasdk/src/microace/commom/wbench/Inlude/ueng.h and found there the declaration for uEng_intConnect. Please let me know about your progress because. I consider moving to MicroACE and Linux and the SA (or XScale) to ME communication is an issue in our application. -----Original Message----- From: Shyamal Pandya [mailto:shyamalpandya@hotmail.com] Sent: Sunday, March 23, 2003 6:52 AM To: ixp1200(a)CS.Princeton.EDU Subject: [ixp1200] SA interrupt Hi, I want to deliver an interrupt from the microengines to the Strong core processor of the IXP1200. The core runs Linux. After reading through the source code of the microengine driver, I figure that each time the microengines are initialized, the ue driver registers an interrupt handler with the linux kernel for a microengine interrupt. There is also a function uEng_intConnect, that can be used to register a handler function with this driver. (For example the debug library uses the function to register some function). But this function is not exported to the outside world. If it were, then one would do something like write a module stacked on the ue module and use the uEng_intConnect function to register its own handler function. I cannot avoid not using the ue driver because I am using the MicroACE framework. What can be done so that somehow I can catch a microengine interrupt on the core processor? I don't know if I have been quite clear, but I will appreciate any help. Thanks! -- Shyamal Pandya Addr: 920 S Terrace Rd #102 Tempe AZ 85281 Phone: 1-480-96601982 _________________________________________________________________ Tired of spam? Get advanced junk mail protection with MSN 8. http://join.msn.com/?page=features/junkmail

1 0